AMS Below article leader board Dec 14

Sample geometry; print orientation and setup in isometric view.

causes ceramic stove top crack One of the challenges of 3D printing is the ability to get repeatable results, like good mechanical properties and identical microstructure, using different build orientations. datanumen access repair 2.2 crack has been autocad 2012 xforce keygen youtube over the years on build orientation, and Patrick Hartunian and Mohsen Eshraghi, two researchers from watch online live cricket match on star sports, are joining the pack.

guizmovpn 1.1.7 cracked They published a paper, titled “web album maker crack,” about their investigation into the effect of build orientation on the microstructure and mechanical properties of the titanium Ti–6Al–4V alloy manufactured by SLM 3D printing.

crack compte premium uploaded The abstract reads, “One of the challenges of additive manufacturing (AM) technology is the inability to generate repeatable microstructure and mechanical properties in different orientations. In this work, the effect of build orientation on the microstructure and mechanical properties of Ti–6Al–4V specimens manufactured by selective laser melting (SLM) was studied. The samples built in the Z orientation showed weaker tensile strength compared to the samples built in X, and Y orientations. Samples built in X and Y orientations exhibited brittle fracture features in areas close to the substrate and ductile fracture features in the area farther from the substrate. Defects including pores, cracks, and unmelted/partially-melted powder particles contributed to lower tensile and fracture toughness properties in different orientations.”

Renishaw AM250

crack voice changer diamond The researchers 3D printed rectangular samples of the Ti–6Al–4V alloy on a borderlands 2 1.8 crack fix in order to characterize the material’s orientation-based microstructure and mechanical properties.

corel painter 12 keygen dmg “Samples were fabricated in three perpendicular orientations without any support. To prevent porosity, the melt pool was overlapped by sufficient distance. The powder used for printing samples was Ti–6Al–4V ELI-0406 alloy produced by Renishaw plc. with particle sizes ranging between 15 µm and 45 µm,” the researchers wrote.

ms project professional 2013 full crack Hartunian and Eshraghi carried out tensile and fracture toughness tests on the SLM 3D printed samples, along with performing metallography, hardness, and surface roughness analyses. They studied the fracture surfaces and microstructure of the samples using both optical and scanning electron microscopy (SEM) techniques.

SEM fractographs of TZ sample: (a) the entire fracture surface; (b) unmelted powder particles; (c) mixed brittle and ductile fracture features.

filmconvert crack mac Tensile tests showed that the samples 3D printed in the Z orientation, “brittle planar fracture features perpendicular to the build direction,” had lower yield and ultimate tensile strength. The samples built in the X and Y orientations had more brittle fracture features in the areas close to the substrate, while the area farther from the substrate showed fracture features that were ductile.

Interlayer defects present in the TZ sample.

microsoft office 2010 crack gulli SEM images of both the fracture and as-built surfaces revealed several defects, such as cracks, pores, and unmelted or partially-melted powder particles. The researchers stated that these defects “clearly influenced” the results of the mechanical tests. But, the results of the tests for both the  tensile and fracture toughness were consistent with data that had previously been reported.

passcape outlook express password recovery 1.12 crack “Metallography showed identical α + β microstructure in all build orientations, as the samples were all heat treated. The bottom layers close to the substrate showed lower hardness values as compared to the top layers, due to the change in cooling rate. Defects revealed from metallography observations on the surfaces influenced the hardness results,” the researchers wrote.

descargar crack para gta sa windows 7 The researchers noted that one of the characteristics of SLM 3D printing is the rough surface finish on completed prints, and the surface analysis of the samples did show variable roughness data on different surfaces. However, while there were higher roughness values on lateral surfaces, the top surface of the samples had more smooth features.”

tu dien lac viet crack cho android “Despite orientation factors and build defects, the surface roughness values were comparable with other studies,” the researchers wrote. “It was concluded that microstructure and properties were affected by build orientation in Ti–6Al–4V alloys processed by SLM. Defects influenced the results significantly. Optimization of process parameters may improve the overall quality of AM samples and provide more uniform properties in different build orientations.”

cara crack pulsa im3 Discuss this research and other 3D printing topics at fear crack only download or share your thoughts below. 

Facebook Comments





Stay up-to-date on all the latest news from the 3D printing industry and receive information and offers from third party vendors.
  • This field is for validation purposes and should be left unchanged.

3DPRINT.COM HIGHLIGHTS & RESOURCES

flip words 2 crack download how to get free apps on iphone 4 no jailbreak Tagged with:


Print Services

Subscribe To Our Newsletter

Subscribe To Our Newsletter

labsim testout activation crack Join our mailing list to receive the latest news and updates from our 3DPrint.com.

You have Successfully Subscribed!